Désolé! Vous avez choisi l'affichage en français, mais cette page n'est pas actuellement disponible en français. Pour le moment, nous vous présentons la version anglaise.

This product has been discontinued.

Computer system requirements:

Below are the minimum computer-system requirements for your FP10.


  • Windows XP SP3 or later (32-bit), Vista (32/64-bit), Windows 7 (32/64-bit)
  • Intel Pentium 4 1.6 GHz processor or AMD Athlon 64 (Turion) (2.5 GHz or faster recommended)
  • 1 GB RAM (2 GB or more recommended)


  • Mac OS X 10.3.7 or later (10.4.11, 10.5.2 or later, or 10.6 recommended)
  • PowerPC G4 1.25 GHz or Intel Core Solo 1.5 GHz processor (2 GHz or faster recommended)
  • 1 GB RAM (2 GB or more recommended)

Windows and Mac Systems

  • IEEE 1394 FireWire 400 Port
  • Internet connection recommended
  • DVD-ROM drive
  • Internal or external 7200 RPM storage drive highly recommended
Note that the speed of your processor, amount of RAM and size and speed of your hard drive will greatly affect the overall performance of your recording system. Also, a more powerful system (faster processor with more RAM) will allow for lower latency (signal delay) that you might experience while monitoring audio or MIDI signals.
Monitor resolution for both PC and Macintosh should be no lower than 1024x768 pixels.

Technical Specifications

Microphone Preamp 1-8 (XLR Balanced)

Type XLR Female Balanced
Frequency Response (±0.5 dB) 20 Hz to 50 kHz
Frequency Response (±3.0 dB) 20 Hz to 150 kHz
Input Impedance (Balanced) 1600 Ohm
THD+N (unwtd, 1kHz @ +4 dBu Output, Unity Gain < 0.005%
EIN (unwtd, 55dB Gain, 150 Ω Input, 20Hz to 22kHz -125 dBu
S/N Ratio (Unity Gain, unwtd, Ref. = +4 dBu, 20Hz to 22 kHz > 101dB
Common Mode Rejection Ratio (1 kHz, 55 dB Gain) > 55dB
Gain Control Range (± 1dB) -4 dB to 50dB
Maximum Input Level (Unity Gain, 1 kHz @ 0.5% THD+N) +14 dBu
Phantom Power (±2 VDC) +48 VDC

Instrument Input (1/4" TS input channels 1-2)

Type 1/4" TS
Input Impedance 1 Mega Ohm

Line Inputs (1/4” TRS input channels 3-8)

Frequency Response (+0,- 0.5dB) 20Hz to 50kHz
Frequency Response (+0/-3.0 dB) 20Hz to 150kHz
Input Impedance (Balanced) 10 KOhm
THD+N (unwtd, 1KHz @ +4dBu Output, Unity Gain) < 0.003%
S/N Ratio (Unity Gain, unwtd, Ref. = +4dBu, 20Hz to 22KHz) >101dB
Maximum Input Level (Unity Gain, 1KHz @ 0.5% THD+N) +20dBu

Line Outputs (1/4" TRS)

Output Impedance 51 Ohms
Cue and Main Output Impedance 51 Ohms

Headphone Output

Type TRS Active Stereo
Maximum Output 150 mW/CH @ 60 Ohm Load
Frequency Response (±1.0 dB) 20 Hz - 20kHz

Digital Audio

FireWire (IEEE 1394) Speed 400mbps
ADC Dynamic Range (Awtd, 48 kHz Sample Rate) 107 dB
DAC Dynamic Range (Awtd, 48 kHz Sample Rate) 107 dB
Bit Depth 24
Internal Sample Frequency Selections (kHz) 44.1, 48, 88.2, 96
Simultaneous record/playback channels and sample rate Single Unit (10 in, 10out @ 24/96K)
Two FP10's (up to 16 in/out @ 24-bit/ 44.1k or 48K)
Three FP10's (up to 24 in/out @ 24-bit/44.1k or 48k)
Note: FP10's and FirePod's can be daisy-chained


Input Connector Type IEC
Input Voltage (factory configured) 90 to 240 VAC
Power Requirements (Continuous) 20W
Internal Sample Frequency Selections (kHz) 44.1, 48, 88.2, 96


Main Chassis
Package type 1U - steel chassis
Dimensions 19"x1.75"x7"
Weight 8 lbs

As a commitment to constant improvement, PreSonus Audio Electronics, Inc., reserves the right to change any specification stated herein, at any time, without notification.